F-body Heads/Cam Swap

Too= ls Needed:

- Set of metric sockets, deep and normal (from 8mm to 19mm is good)
- Set of Metric wrenches (8mm, 10mm, 13mm, 15mm, 18mm, 19mm)
- Metric "Gear" wrenches (not absolutely necessary, but REALLY handy)
- 8mm hex allen wrench
- Torque wrench for 20lb/ft up to 150+lb/ft
- Various socket extensions, ranging from 3" to 12"
- Medium length socket wrench
- Large 1/2" drive breaker bar
- Piece of pipe to slip over breaker bar handle
- 1/2" drive 24mm socket
- Adapter from 1/2" drive to 3/8" drive
- 3 armed pulley puller
- Felt tipped marker (if using stock headbolts)
- Plastic ice scraper
- Prybar or large flathead screwdriver
- Medium sized pliers (for hose clamps)
- Medium sized flat head screwdriver
- 3/8" fuel line discon= nect tool
- 3+ gallon Bucket
- Optional: Flywheel locking tool (for automatic transmission cars only)
- Optional: Longer crankshaft pulley bolt (Size specs coming soon)

Par= ts/supplies you will need:

Parts:
- 2 LS1/LS6 engine heads
- 1 Camshaft
- Optional: Underdrive crank pulley
- Optional: blueprinted oil pump
- Optional: New timing chain
- Optional: New OEM 2001 style intake manifold

Bolts/gaskets:
- 2 GM headbolt kits (2x GMPN 12498545)
- OR ARP head bolts or head studs
- For 97-01' style heads, buy 1 pair of headgaskets<= /span> (1x GMPN 12498543)
- For 02-03' style heads, buy 1 pair of headgaskets<= /span> (1x GMPN 12498544)
- 2 AIR tube gaskets (2x GMPN 12553617)
- 2 Water pump gaskets for 1997-98 model cars (2x GMPN 12559271)
- 1 front engine seal (1x GMPN 12561244)

Supplies:
- 7 quarts of oil
- new oil filter
- Jug of dexcool compatible coolant
- RTV Hightemp silicon gasket maker
- Locktite (red tube)
- Tube of Anti-seize
- Shop rags, roll of paper towels
- One can of compressed air with plastic straw (look in computer section = of an electronics store)

Preface<= /span>

Like many others, you are looking for more horsepower. The only real obstacle keeping us from the horsepower we want is money. So, to save money and put it towards more parts, I decided to do my own labor. You'll be surpris= ed how easy most of the install is,= and you may also be surprised ju= st how much stuff there is to do!
- GTP Stage 2 LS1 Cylinder heads, purchased from Thunder Racing

If you still have the stock 97-00 intake manifold on there, now is a good time to put the 2001+ version on. = Only 15-20 minutes of additional labor is needed.

Pictures= of the parts:

<= /p>

All the parts you should have bought, plus optional stuff. Hea= ds, cam, timing chain, underdrive pulley, new oil= pump, ARP head bolts, and some gaskets.

<= /p>

Pics of double springs (more reliable than standard single valve springs). The sprin= gs pictured (Comp 987) will require head modification to the spring seats to allow space for them to fit. Thunder Racing had this done to my set of heads for extra reliability.

<= /p>

This is what a ported intake port looks like. Th<= st1:PersonName w:st=3D"on">is is a 5.7L LS1 style head casting.

<= /p>

This is what a ported exhaust port looks like. Th= is is a 5.7L LS1 style head casting.

NOTE: Some pictures from = this install are from an f-body, some are from a corvette. Any part that specifically deals in something F-body specific wil= l be shown using a photo from the appropriate car.

Lets begin:

PART 1: Clearing out the front of the car
Time = to complete: 1 hour

<= /p>

First get the front end of your car in the air. Drive it on ra= mps and chock the rear wheels with some wood/rocks/wheel chocks/whatever. You don't need to jack the car up. Pop the hood and disconnect the ground cable going to the battery, and once the car is cool enough, remove the cap to the radiatorr. Grab a bucket and place it under the pet= cock valve on the passenger side of the radiator. Open the valve and drain the coolant. As the coolant drains into the bucket, continue on with the next step.

<= /p>

Using a flathead screwdriver untighten the clamp where the intake duct meets the throttle body. Disconnect the IAT wire going to your air lid= and the MAF wire going to your MAF. Disconnect rubber AIR hose from lid (2000+ models) and remove the air lid/coupler/maf assembly from the car.

<= /p>

Using a 15mm socket wrench or 15mm wrench on the drive belt tensioner, relieve the pressure on the drivebelt and slide the belt off the water pump and remove the belt.

<= /p>

Disconnect the PCV rubber hose going to the throttle body on the passenger side. Unclip the electric connectors going to the throttle body. If you haven't done the TB Bypass mod, grab a pair of pliers and remove the 2 rubber coolant hoses g= oing to the throttle body.

Now, disconnect your throttle cable(s). You need to open the throttlebody by hand, then push the metal bar at the end of the cable out of the throttle "cam" and free the cable. On non-TCS cars there will be an additional cable for cruise control that just slides off (look at it closely). Now, using a 10mm sock= et and 3" extension, unbolt the 3 bolts holding the throttle body to the intake manifold and remove the throttlebody f= rom the car.

<= /p>

Using a pair of pliers, now slide the spring clamps off the 4 hoses that go to the water pump. There will be 2 smaller hoses going into= the passenger side of the pump, 1 big one going to the passenger side of the pump, and one big one going in towards the center of the water pump. Once= the clamps are all slid back some, pull or pry (using a large flathead screwdriver) the hoses off the pump. Coolant will most likely start pouring out of some of these....you can try to catch so= me of it in a bucket but I usually just let it hit the ground.

Now, there are 6 10mm bolts that hold the pump to the block, 3 on each si= de. See diagram of the pump on the left for their locations. Unbolt all 6 bol= ts and remove the water pump from the car. Coolant again will start leaking = once you loosen all the bolts, its inevitable. Don't worry about it.

<= /p>

If you have a power steering cooler inline in your upper radia= tor hose, go ahead and disconnec= t the radiator end of that hose from the radiator, and we'll leave the whole ho= se in the engine bay for the rest of the install (so we don't have to mess w= ith those power steering lines).

Now, this part is tricky. We need to remove the radiator. F= irst unbolt the plastic radiator shroud/air lid base, it is held to the frame by 2 10mm bolts on each side of the car. Next, get under the car with a small flathead screwdriver and unclip both fan electrical connectors (using the flathead screwdriver, as its impossible to do with your fingers), and unclip all the wiring rings hold= ing the wiring harness to the fan shroud. You're all done under here, go ahead and get back up to the top of the engine bay and grab a friend to help wi= th the next part.

Now, you have a big assembly here....the fan shroud is mounted on the radiator via 4 slide in tabs, and on the front of the radi= ator the AC condenser (looks like another radiator) is attached to the radiator with 4 tabs. We need to slide the AC condenser UP about 2 inches to dislodge t= he tabs and get the radiator free from its grasp. This will take some cursing and a good light source so you can see the 4 slide= in tabs I'm talking about. Once the AC condenser is loose from the radiator, both of you need to lift the radiator up and out= .

Lifting the radiator up and out....that sounds so easy doesn't it? HA! Th= is part can sometimes be frustrating, so be patient. While trying to remove the radiator, you'll need to make sure th= at on the drivers side you don't catch on the AC condenser hard lines. The large coolant hose will want to snag on things. Keep wresting with it until the radiator/fan assembly comes out totally, = and set it aside. The AC condenser will stay in the car for the whole install. NOTE: in the pic on the left, I have my fan s= hroud and radiator separated for cleaning purposes.

<= /p>

This part is fun....the removal of the power steering = pump. Rather than remove the pulley and take the pump off the bracket, we'll ju= st remove the whole unit assembled. This takes some patience...about 10 minutes of slow wrenching. Use the stubby = 15mm wrench and using the open end, loosen each bolt a little at a time to slo= wly work the bracket slowly off the head. The bottom bolt will be a little ha= rd to get due to a power steering line, but it can be gently held out of the= way by a helper. The far drivers side bolt will also be a little blocked, and= this is why you need to slowly work your way around the bolts and turn each one a= few turns at a time...all while pulling the bracket off the head. It sounds complicated, but its not. You'll figure it out when you see it...its easy. The pic on the left shows the wrench on the b= ottom most bolt..just so= you know it IS possible.

Once the assembly is loose, = tie it off to something in the engine bay to help support it. A wire tie works w= ell for this, or a rope or bungee cord. Notice that all lines are still attached so no bleeding or draining= is nessiary.

Part 1 Complete
You h= ave now successfully removed the cooling system and intake ducting from your f-body!

Part 2: Removing the Intake and Exhaust
Time = to complete: 2-6 hours

<= /p>

On each side of the engine, there = is a metal AIR tube bolted onto the exhaust manifold or header. Each is held onto the exhaust by 2 10mm bolts. Re= move them. The AIR tubes immediately connect to a rubber hose. Using a flathead screwdriver, undo the plastic clamp on the rubber hose and remove the AIR tubes totally from the engine bay. Remember which one goes to which side.= ...I usually keep the parts stored on the proper side of the car just to make things easier when we reassemble.

On the passenger side of the car, unbolt the oil dipstick tube mount from= the head and with a firm tug, pull the dipstick tube up and out of the engine bay.

<= /p>

Now disconnect al= l 8 plugwires from the coilpacks. Try not to pull on the wire, but instead pull on the boot that connects to the coil. Next, disconnect t= he wiring harness that goes to the coilpacks. Its a large white weatherpack connector, labeled in the photo.

Next we need to remove the coil packs from each valv= ecover. On 98 LS1's, each coil pack is bolted to the valve cover separately. On 99+ year models, all the coil pa= cks are on a bracket and the bracket is then mounted to the valvecover. Depending on = your year, either unbolt all the coil packs individ= ually ('98), or unbolt the 5 10mm double-ended bolts (using a deep socket) and = remove the coil bracket with coils still attached. On 99+ year model cars, there= may or may not be a bracket mounted to the backmost bolt. If there is, undo the nut and pry the bracket off wit= h a big flathead screwdriver, and then unbolt the final bolt to remove the coilpack rail.

<= /p>

Now that we've got the ignition di= sconnected, lets take care of the fuel system.

On each fuel injector on the intake manifold, you'll see a metal clip on = the bottom of the connector. You need to push thi= s metal clip in and compress it, then pull the electrical connector off of = the injector. Some of them will be tough, while others are easy. Disconnect all 8.
Next, unscrew the fuel pressure test port cap on the tip of the drivers side of the fuel rail. Grab a big rag and a = phillips screwdriver, and while surrounding the testport with the rag (incase of high pressure spra= y!), press in the schraeder valve (like on a tire)= to relieve any fuel pressure that may be left. Chances are nothing will spray out since the car has been off so long, but its better to be safe than sorry. Now, get your 3/8th inch fuel line disconnect tool and put it around the hard me= tal line coming off the fuel rail. This tool will slip under the connector on the rubber fuel line and that will = undo the metal tangs that hold it onto the fuel rail. See photo for clarificat= ion. Swing fuel line out of the way and have rags handy to catch all the fu= el that will be spilling out of the fuel rail.

<= /p>

In the rear drivers side of the eng= ine bay, you'll see a big black metal brake booster that has a rubber hose go= ing to it. Using a pair of pliers, move the spring clamp and then pull the ho= se off the brake booster. The other end of this<= /st1:PersonName> hose goes to the intake manifold....we'll leave the manifold end connecte= d.

Next lets disconnect the 2 lines going into the front of the intake manifold. the one on the passenger's side is the PCV connection. You need a deep 10mm socket to unbolt the ground strap th= at goes to it, and then you can pull the PCV line out of the manifold. On th= e drivers side, there is a fuel EVAP line. Compress the grey plastic clip and at the same time, pu= ll the whole thing away from the manifold and it'll slide off easily.

Now unbolt the 10 8mm bolts that go into the top of the manifold. There <= st1:PersonName w:st=3D"on">is no need to unbolt the bolts holding the f= uel rail on, those can stay on. For the rear 2 bolts, it may be easiest to us= e a 1/4" drive ratchet or an 8mm gear wrench as clearance under the cowl= is tight. The rear 4 bolts won't come out al= l the way as they'll hit the cowl, so you'll need to hold them up either with t= ape or with your hand for the next step. Now, lift the whole manifold up and = off the heads about an inch and try to slide it forward about 6 inches (making sure those rear 2 bolts don't snag on anything). Now we have access to the back of the intake manifold. Disconnect the electrical connector to the back, and then pull the rubber boot/vacuum line off the back as well. The manifold is now 100% disconnected from t= he car and can be removed from the engine bay (note, cautiously route the brake booster hose through the mess of wires while you remove the intake manifold...don't let it snag any wires on its way out). Try not to tilt t= he manifold too much as the fuel rail is probably still full of gasoline and it'll spill everywhere.

<= /p>

Now, if you have a '98-'00 car with= a stock intake manifold, you'll have a big X shaped coolant pipe bolted to = the heads going across the engine valley. If you have a 2001+ intake manifold= (on any year car), you'll have the new style coolant pipe which just runs to = the front of the heads, and then you'll have a plug on the back of each head. Remove whatever coolant pipe setup you have and set it aside. Everything = is held on with a total of 4 10mm bolts.

<= /p>

Get underneath the car with a deep 15mm socket wrench and some WD-40 or equivalent. You should see where your Y-pipe mounts to the exhau= st manifold. Spray down the 3 nuts on the studs coming out of the manifold w= ith WD-40, and then try to break the 3 nuts free. Initially they may be tough= to break free but should come loose with some effort. While you are under he= re, follow the wire off of the O2 sensor until you see an electrical weatherpack connector. Disconnect this connector.

Repeat for the other side of the car.

Note: if you have aftermarket headers, a similar procedure can be = used to undo the intermediate Y-pipe from the header collectors.

<= /p>

Now get back up into the engine bay with a 10mm socketwrench and a couple of extensions. On each ma= nifold there are 6 10mm bolts holding them to the head. I recommend undoing the backmost bolt first, and leaving one of the middle bolts until the end. O= nce all 6 on one side are done, the exhaust manifold should be able to drop down = out of the way enough so we can get to the head bolts. If you are removing th= ese stock manifolds and will be putting headers on, these stock manifolds sho= uld drop down through the bottom but will require you to jack the car up off = the ramps to get enough clearance.

Repeat for the other side of the car.

Note: if you have aftermarket headers, the same 6 bolts will still hold them to the heads. However, you may find the header doesn't want to easily sink down enough in the engine bay to give us access to the bottom= row of big head bolts. If this <= st1:PersonName w:st=3D"on">is the case, you need to totally remove the headers from the car. Mac headers will pull up through the top, FLP's, Gro= tts, Hookers will sink down through the bottom. This will require removal of your ypipe too (which is pretty self explanatory once you go under there and look, as long as your= ypipe isn't WELDED to your catback (I've actually seen sh= ops do this#!@)

Part 2 Complete
Now t= hat the intake and heads are off, we're set to remove the valvetrain and heads. This will mostly = be busy work, nothing complicated.

Part 3: Removing the Heads
Time = to complete: 1-3 hours + 1-4 hours for cleaning of cylinder head mating surf= ace

<= /p>

Start by unbolting your valve covers and removing them. 99+ mo= dels use 4 8mm center bolts on each cover. 98 models use perimeter bolts around the edge of the cover. On the drivers side you'll need a flathead screwdr= iver to pry up the PCV line out of the back, and on the p= sg side you will need to slide off the 2 rubber PCV hoses from the valve cov= er (the front one may still be attached to your throttle body). On an LS6 th= ese may be configured differently (the PCV plugs into the engine valley cover instead on an LS6).

Once both are removed you'll see your valvetrain. There are 8 rockers on each side, and each is= held in by an 8mm bolt through the center of the rocker. Get a cardboard = box and remove all 16 rockers, and its generally good practice to keep all the rockers in order (keep them organized in the box so you know which side a= nd what order they came off in). Make sure you get a SOLID grip with = the socket on the bolt as you don't want to round the bolt off. It'll take so= me force to break the bolts free. Once they are removed, grab the long metal rocker pedestal on each side and store it with the rockers. Then reach in with your fingers and remove all 16 pushrods. They just pull out. =

<= /p>

Now for the fun part. Reach back by the firewall and feel the = back wall of each cylinder head. Each year of cars seems to have different bol= ts on the back of the heads. On most it seems there is 1 wiring harness bolted to the back of the passenger side head. Try to se= e if you can get a socket wrench or an open ended wrench on the bolt holding t= he bracket to the head......if you can't, don't worry and we'll leave this connected for now.

On the Drivers side there are probably 2 things connected. First, there w= ill be either a 13mm or a 15mm bolt holding a bracket on the head. Using a bo= x or open ended wrench, break the bolt free. This<= /st1:PersonName> will be very annoying and may seem impossible. Sometimes I put the open e= nded wrench on the bolt best I can, and then hit the other end of the wrench w= ith a hammer. Once you break it free, it'll unbolt by hand. Once the bracket mounting bolt is free, feel = back there some more and you'll again find another 13mm or 15mm bolt going int= o the back of the drivers side head. This one will have a wire going to it, and is a ground cable. Once again, break it free= and unbolt it. Remember where these things are when you are unbolting them as they'll need to go back on the new heads later. I'd thread the bolts back into the new heads for safe keeping.

We're now ready to unbolt the heads. Lets star= t with the passenger side. There are 15 bolts holding each head to the engine bl= ock, 10 large 15mm bolts, and 5 smaller 10mm bolts. Remove the 5 smaller 10mm bolts first, and then using a large breaker bar and a 15mm socket+3" extension, unbolt the 10 big 15mm bolts. Once all the bolts are out, pull= up on the passenger side head and you should hear a "SPLASH" of coolant going everywhere on the floor. Don't sweat it. Now, if you couldn= 't get that electrical connector off the back of the head earlier, pull the = head forward as much as you can and look at what you are dealing with back the= re. You'll see there is a metal = snap type connector holding the wire to the head. If you compress it with your hands and pry with a flatheaded screwdriver y= ou can free the big electrical harness from the head, and can then remove the he= ad totally from the engine bay. Take some paper towels or a cloth and soak up all the coolant out of each cylinder.

Now repeat for the drivers side, again being c= areful to make sure everything from the back of the head is indeed disconnected. =

<= /p>

Pull up both head gaskets and dis<= /st1:PersonName>card them. Underneath the gaskets, you can see 2 10mm bolts holding each lifter retainer cup (the brown plastic things holding 4 lifters each). Unbolt the lifter retainers making sure to NOT DROP THE BOLT, and then pull them up = and out. You should get a few lifters still stuck in each retainer, grab the = ones that didn't come out and put them in the lifter retainer in their proper place. Again, keep the lifters in order just for good practice. Repeat for the other side of the engine. Place a rag in each lifter section (4 secti= ons on each side of the block) to keep debris out of the engine.

Now take your plastic ice scraper and start scraping off all the chunks of graphite off the engine block where the gasket was. You don't n= eed to see bare metal, but the WHOLE gasket surface needs to feel totally smo= oth to the touch. Pay special attention around the alignment dowels in the fr= ont and back, as gasket material likes to stick around them. This process should take 5-10 minutes per side= if you are very thorough, and the surface should be nice and smooth (although it'll still be colored like the graphite gasket).

Repeat for the other side.

<= /p>

Next we need to clean the bolt holes. I clean them in a 3 part process as this step is very important. .

Bolt Cleaning Part 1: Take your can of air with the straw attached= to the nozzle and get the straw as deep down inside the bolthole as possible, then blast it out with air. Its important to blow it out from the bottom to get as much coolant out as possible. If you have an air compressor, you can blow from the top of the bolt hole, but a lot of coolant will stay in the bolt hole, it is however, still better than nothing.

Bolt Cleaning Part 2:Once all the bolt holes are blown out, roll up a paper towel into a tight roll about the thickness of a headbolt, and push i= t down the headbolt hole. You may have to "thread" the paper towel in to get it all the way to the bottom= . If the towel comes out with a coolant soaked bottom, chop off the wet bit wi= th scissors or roll a new paper= towel and repeat the process until it comes out dry. Do this for all 20 big headbolt holes (10 on each sid= e).

<= /p>

Bolt Cleaning Part 3: Take a grinder or a = dremmel and grind off the threads on a strip on both sides of ONE USED lon= g headbolt. The goal here is to make it a tap for cleaning headbolt thread= s, as we need space for the grit and grime to stick when we thread the bolt in.= It should look similar to the photo on the left.

Once you have an old used bolt modified, thread it in each bolt hole all = the way to the bottom and then remove it until the bolt comes out clean. You'= d be amazed at how much grit gets in there. In addition, if you feel the bolt = get "springy", you are compressing coolant in the hole and you'll n= eed to dry it out some more. Once this step is done, the block is all cleaned and we're ready to proceed! <= /span>

Part 3 Complete
Congr= ats, your engine cylinder heads are now removed and the engine block is all nice and clean, ready for the new par= ts.

Part 4: Installing the new cam
Time = to complete: 1-3 hours

<= /p>

On a 6 speed car, put the shifter in 4th gear and make sure the parking brake is on tight. O= n an A4 car, you'll need to drop the starter and either in= stall the flywheel locking tool or wedge a screwdriver in. The starter is held in by 2 13mm bolts for 99+ models or= 2 15mm bolts for 98 models and is on the bottom rear passenger side of the engine. You can leave the wires attached.

Once the engine is locked do= wn from spinning, use your large breaker bar, a 3" extension and a 24mm socket on the crankshaft pulley bolt that goes directly into the crank through the center of the large pulley. You may need a 2-3 foot extension= of pipe to slip over your wrench to break this bolt free. Once its broken free, you should be= able to unscrew it by hand. Once the bolt is out, either thread it back in 4 full turns, or if you purchased a 1" longer metric crank bolt, install it all the way at this time. Now install your 3 arm pulley puller, mounting the hooks of the thr= ee arms on the inner part of the stock pulley. If you already have an underdrive pulley on there, either pull it off usin= g a 3 screw type puller, or be VERY careful and grab onto a lip of the underdrive pulley (on the fbod= y ASP pulley there is a ridge = half way back that can be pulled on safely with a 3 arm puller). Keeping the pulley puller arms all secure and aligned, begin to tighten the bolt on t= he puller and crank on it until the pulley either comes loose, or hits the h= ead of your crank bolt. If it hits the head of your cran= kbolt, loosen the pulley puller, unturn the bolt 1-2 turns, and re-try it again. The key when you back your crank bolt out mor= e, you are putting MORE stress on less and less of the threads...however, towards the end of pulley removal it will come off easier and easier so t= he stress isn't enough to damag= e the crankshaft threads.

If you get the pulley as far off as it'll come without totally removing t= he crankbolt and the pulley is still firmly on there, give it a good tug or a tap with a rubber mallet..= .it should be hanging on by just a hair at this point. If you have the longer crank bolt, thi= s won't be an issue.

<= /p>

Next, we'll unbolt the timing cover. There are 10 bolts holding the timing cover to the engine, 8 on the front, and 2 on the bottom front= of the motor. Remove all 10 10mm bolts. Remove the timing cover once all bol= ts are out...it may be kinda glued at the bottom= , just give it a tug.

<= /p>

Now lookie what's in there. The big gear you see is the = gear mounted to the end of the camshaft and is held on by 3 10mm bolts. The chain is of course the timing chain, and the big metal block at the bottom is the oil pump.

Unbolt the 3 cam gear bolts and remove the gear, letting the chain droop = down into the oil pan for now. Thread one or two of the c= amgear bolts back into the end of the cam so we'll have something to grab later. Next you'll see a black/brown cam retainer plate behind the gear, held on= by 4 10mm bolts. Unbolt and remove this too.

<= /p>

This picture shou= ld show exactly what you are looking at in your engine bay now. The cam is sitting there, waiting to be yanked out n= ow. Before we remove the cam, make sure of the following:=
- All 16 lifters should still be uninstalled at this point. If for some reason you reinstalled them, remove them again
- Radiator should be out of the car, and the A/C condenser should be able= to swing forwards/backwards and lift up at least a foot or so
- You have the cam bolts threaded in good for use as grips to pull the cam out. NOTE, if you have your waterpump bolts handy, thread one or two of these in the end of the camshaft. The e= xtra length will give you more leverage to pull the cam out and keep it level. Just don't forget what those bolts go to!

<= /p>

Now, grip the bolts on the end of the cam, and gently start pulling the cam out. The key here is to be gentle with this part.= The cam will need to be constantly spun as you are removing it. You need to e= nvision what is going on inside the motor, your cam is basically going through a few holes that suspend it. Once you pull the cam out a bit, its going to drop down some = and the lobes are going to be getting caught on the cam bearings in those "holes", which is = where the gentle spinning and tugging comes into play.

Whatever you do, don't force the cam if it feels like its caught, just keep turning until it wants to naturally slide out more with gentle force. Once the camshaft if 1/4 of the way out, use 2 hands and tr= y to leverage the end of the cam to keep the whole camshaft even, rather than dragging it out of the engine. Once you support the cam with two hands yo= u'll see its much easier to remove as its not getti= ng caught on everything inside. Once the cam is<= /st1:PersonName> 75% out, have a friend move the AC condensor UPWARDS at about a 30 degree angle. Move it up until you have just enough room to pull the cam out totally and set it aside. Note that the AC condenser lines are not designed to flex TOO much so only move it up out = of the way as far as you need to for the cam to be removed.

<= /p>

Get your new cam out of the box, coat the whole thing with fre= sh motor oil, and transfer your 3 camgear bolts = (or waterpump bolts if you were using those) to the end= of the new cam so again you have a handle to grip onto.

The installation is the reve= rse of the removal, for the first 75% of the install make sure you support the camshaft with two hands and keep it as level as possible as you slide it = in. Don't push it into the motor with much force at all, and spin it as neede= d. The last 25% of the cam install you can only do one handed, so just gently turn the cam, wiggle the cam, and apply light pressure to it until it goes totally into the motor like before. This process may take 5-10 minutes so don't rush it.

Once in, re-install the cam retainer plate and its 4 10mm bolts. I usually put some locktite on the 4 bolts and the GM t= orque spec on them is 18lbft.

<= /p>

Optional: If you purchased a new oil pump and/or a new chain, you'll need to complete this= step.
First, unbolt the 4 10mm bolts holding the oil pump to the engine block, making sure not to drop any into the oil pan.

Now we need to unbolt the oil pan to lower it some. It is held on by 8 or 10 bolts around the perimiter= , some M8 and some M10 (10-12mm hex head bolts). You should be able to loosen th= em all enough just to get the pan to drop 1/2". It may need some prying= to break it free at first.

Next, grab a 10mm wrench and unbolt the pickup tube bolt...it holds the pickup tube to the oil pump. The Once its loos= e, unthread it and remove it with your fingers making sure not to drop the bolt into the oil pan. Now grab the pump with one hand and with your other hand or a screwdriver, push the pickup tube downwards into the oil = pump to separate it from the pump. Once its separat= ed, pull the pump off the front of the engine crankshaft.

You can now remove your old timing chain if you need to. Place the new ch= ain over the cranksnout and let it droop down like before. Leave the oil pump off the car for now.
End Optional

<= /p>

This step is one of the KEY parts of the install. If y= ou mess this part up, you risk major engine damage once you try to star= t the car up later on. However, we'll verify everything is right before we go further, so don't worry too much. The goal here is to get the cam gear back onto the front o= f the cam, with the chain in place. That part is easy enough, the hard part is getting the dots lined up. There is one dot on the face of the cam gear, and one dot on the front of the crank gear (behind the oil pump).

Thread your old crankshaft bolt back into the crank and with a wrench, turn the crankshaft until you see the small = black dot pointing straight up. See picture on the left for reference. Next, in your hand, orient cam gear so dot is on bottom and hold it up to the front of the cam....see the smaller 4th h= ole in the cam gear? That is whe= re the cam alignment dowel goes in. Spin camshaft by hand so dowel looks like it= 'll line up with cam gear properly to align the dots. Put the timing chain on= the crank gear, and then put it on the cam gear, holding the cam gear up with your hand to keep tension on the chain. CAREFULLY, try to get the camgear to seat on the front of the cam. if you don't get the hole and the dowel aligned just right, you're just going to push the cam back into the block.

If you are having trouble aligning it up, try threading a cam bolt through the gear into the cam to grab it and line it up like that. Most likely you are going to have to keep moving the chain on the cam gear until you get = the dots lined up just perfect, and you'll have to get lucky and have the cam oriented just perfect so the gear seats on like it should. If all this sounds complicated, just look at the pict= ure on the left and make yours look exactly like that. :) Don't get mad if this part takes 20-30 minutes of trying until = it all looks correct. Once its all together, make 100.000% sure the dots = are lined up exactly. You cant be off by a few deg= rees due to the sproket/chain setup, you can be of= f by one tooth at the minimum so if you are off you'll see it. If it looks off= a little bit, turn the crankshaft by hand again to see if the 2 dots do ind= eed line up when they are straight up and down...sometimes if your crankshaft= is 5 degrees too far , the cam gear will look like its off 10 degrees or so and you'll think the= re's no way they'll line up exact...when in actuality you just needed to get t= he crankshaft straight up.

Now bolt the cam gear to the cam using the old 3 10mm bolts, again, placi= ng locktite on the threads. These should be torqued to 26lbft.

<= /p>

Optional: If you removed your oil pump in the previous step, you'll need to do this to reinstall it
Find your oil pump pickup tube O-ring, it may be brown or blue in color. = It will either be inside the opening of your stock oil pump, or it'll still = be on the snout of the pickup tube. If it was inside the oil pump, remove it= and place it on the snout of the pickup tube...just seat it on there, don't f= orce it down any more than it wants to go naturally.

If you bought a new oil pump, get it out now and place your old pump asid= e. Now, push the pickup tube downwards with one hand, and with the other, tr= y to line up the gear on the oil pump with the gear on the crankshaft and push= it on. Again, this may take a f= ew minutes to get the gears all lined up. Once the pump slides on, rotate it= a little and try to line up the snout so it'll slip into the oil pump nice = and centered. If you try to insert it off center, you run the risk of chewing up the o-ring which will mean= you have very little oil pressure and have to tear all this apart to get back in here to replace it. You don't want that, so make = sure you insert the pickup tube nice and centered. It shouldn't take much forc= e at all to push it in. Once its in, apply locktite to the old pickup tube bolt and re-install= it. The torque specs are about 9 lbft, so just ti= ghten it with a small wrench so its snug but don't go crazy on it, as its a really small bolt and the threads will strip out wi= th too much force.

Apply locktite to the 4 10mm oil pump bolts a= nd reinstall them, torqueing them to 18lbft.

Now, retighten up the oil pan bolts. The smaller bolts get torqued to 106 INCH lbs, or about 9 foot lbs, while the bigger bolts get torqued to 18ftlbs. Note: You WILL break those smaller headed bolts if you go past the= 9 ftlbs as specified. End Optional

<= /p>

Now lets work on getting the front buttoned back up. Grab your timing cover and look at the hole in it...the= re is a big round seal that is pressed in from the front. Flip the timing cover over and lay it across s= ome 2x4's or across a concrete step (like shown in the picture) so you have r= oom for the seal to pop out and not hit anything. Next, grab the biggest flat head screwdriver you have, and use it as a punch by hitting it with a ham= mer to drive the seal out from behind. Move the screwdriver to different part= s of the seal after each whack so you don't just press one side of it out. Aga= in, the picture shows this proce= ss. You may have to hit the seal a lot and with much force to get the seal lo= ose.

Once it pops out, flip the timing cover over and lay your new seal in pla= ce as centered as you can get it. If you have a block of wood, lay it across= the seal and hammer on it to try to seat the seal properly. If you don't have= a block of wood, just start by trying to tap the seal in on all sides until= it seats, and then give it a few good whacks until its totally seated.

<= /p>

On the very bottom of the timing cover, there may be some sili= cone sealant remaining, and if so, remove it. Next apply a bead of hightemp RTV sealant across the bottom of the cover= , from one end to the other, like shown in the picture.

Now set the timing cover back in place on the front of the motor and start hand threading all the 10 bolts back into place, only turning each bolt in 5-6 threads worth for now. The timing cover needs to stay loose for now. =

<= /p>

NOTE:If you purchased an und= erdrive pulley, now is the time to i= nstall it, otherwise, use your stock pulley. Either way, the instructions are the same for install.

Seat your pulley back onto the snout of the crankshaft as best you can by hand. If you purchased a longer crank bolt, start threading this in now and pull the pulley on about a 1/4= or 1/2 an inch and remove the longer bolt. Use your old stock crank pulley b= olt to pull the pulley onto the crankshaft until the bolt seems to get imposs= ible to turn. Grab your biggest torque wrench and attempt to torque that bolt = down to 240lbft. I have always stopped at 200lbft on my installs and I've never had a problem, so if you can't hit 240 (which I never have), don't worry about it. Now, break the bolt free and remove it.

Take your NEW crank pulley bolt and thread it in all the way by ha= nd. Torque this bolt to 37lbft. = Now, we need to stretch the bolt into place. Get your breaker bar and pipe extension, and try to turn the bolt 140degrees past where it is at now, keeping in mind the engine will be trying to turn some and those are degrees you can't count. Again, I always seem to get about 90-100 degrees worth (estimating, knowing what 90 degre= es looks like) and leave it as is so don't worry about going crazy here.

Once the pulley is installed= , the timing cover should be nice and centered around it, so we can now tighten all 10 of those timing cover bolts. Torque them to 18lbft on the bolts you can get a torque wrench on, and just make the oth= ers you can't get the wrench on about as tight as those. Reinstall the A/C be= lt at this time.

Part 4 Complete
Thats it for the cam/oilpump/timingcover/pulley swap. Lets get back to the heads now.

Part 5: Installing the heads
Time = to complete: 2-4 hours

<= /p>

Swap Coolant temp sensor and coolant plug to new heads. Your n= ew heads are identical, so it doesn't matter which head you put the coolant = temp sensor or coolant plug in.

The Coolant temp sensor which is found on the exhaust side of what was the drivers side head can be unscrewed with a deep 19mm socket. If you have teflon tape or gel, put some on the threads and hand thread the coolant temp sensor in as far as it'll go by hand. Torque this to 15lbft.

The Coolant plug is on the e= xhaust side of the old passenger side head, and goes in the exact same place as = the coolant temp sensor did. This is the only thing that will differentiate th= e two heads from this point on in = the install as they are otherwis= e the same.

If you didn't buy new sparkplugs, swap the sparkplugs over now. If you bo= ught NGK TR55's, leave them at stock gap, put some anti-seize on the threads a= nd put the new plugs in.

<= /p>

Now, place your lifters and lifter retainers back in place like they were when you removed them. Try to keep them oriented exactly like t= hey were before you took them out. If you don't remember how they came out, d= on't worry, and just put them in however. Its not t= hat big of a deal. The small centerbolt that hold= s each lifter retainer down is 10mm. Apply locktite to the threads and torque them= to 106 lb INCHES, or about 8 lbft. DO NOT= OVER TIGHTEN THESE, or you will strip the threads out.

Inspect the engine block surface and you should see 2 dowels sticking up about 1/4" on each side of the engine, they are 1/2" in diamete= r. If you don't see these 2 dowels, inspect your old heads and see if they c= ame off in them (which is very r= are), and put them back in the block.

Now, lay the headgaskets on the block. If you= got the 97-01 graphite style head gaskets, each headgask= et will say "This side up&= quot; and will also say "FRONT", make sure the "this side up" is up, and the "front" part is to the front......the two gaskets are unique, so make sure you do = this part right! If you got the new 02+ style = head gaskets, they are identical so just make sure you have the right side fac= ing up. The gaskets will line up with the dowels discussed above.

<= /p>

Now lay the heads on the block, setting them on the 2 dowels. Reattach anything you discon= nected on the back of the heads earlier. NOTE, on my car, I never reattach the harness on the back of the passenger side head, nor do I remount my AIR bracket. The only key things to reattach are the black ground wire(s), those MUST be bolted down good.

If using OEM GM headbolts:

<= /p>

Now, grab a socket wrench and lightly turn= the bolts until they stop. Now for the very preci= se part. You need to get your torque wrench out now and fit it with a 3" extension and a 15mm socket.

Using the sequence illustrated above, torque all 10 15mm bolts to 22lb-ft.

OPTIONAL: Safety check! One one side of the motor install 2 pushrods (one exhaust, one intake), the rocker pedestal, = and two rockers...then turn the motor over by hand two full turns. While this method wont be= exact, if the engine didn't stop when you were turning it you most likely instal= led the cam correctly. If it felt like it stopped at one point and wouldn't go further, chances are a pisto= n is hitting a valve and you need to disassemble things and go back to the dot to = dot part, OR, your cam is huge a= nd the piston to valve clearance is ZERO (it'd take a really big cam for this to happen)

Ok, now for a GREAT tip from Scott99Z. Take a felt tip marker and draw a horizontal line on the head of each bolt. Thi= s is very important.

Now, using the sequence illustrated above, turn all 10 15mm bolts an additional 90 degrees using a large socket wrench and a lot of muscle. Tr= y to get as close to 90 degrees as possible...you may have to do multiple turn= s of 30 degrees or 2 turns of 45 degrees. When done all the lines on the bolt heads should be totally vertical.

Next, again using the sequence above, turn bolts 1 through 8 another 90 degrees. This will take an i= mmense amount of effort...if you have a buddy helping both of you should turn the wrench simultaniously. These 8 bolts will now= all have horizontal lines on them

Using the sequence above, turn bolts 9 and 10 = an additional 50 degrees. Again, this will take a lot of effort. 50 degrees should result in a diagonal line on= the bolts

Finally, using the sequence above, torque bolts 11 through 15 to 22 lb-ft= .

If using ARP headbolts:

<= /p>

Apply the moly lube that came with the ARP bo= lts to the threads, as well as under the head of the bolt and both sides of the washer. Only a light coating is needed. If you don't have the included moly l= ube, put some motor oil on the threads.

Torque all 15mm bolts to 30lbft in the torque sequence above.

OPTIONAL: Safety check! One one side of the motor install 2 pushrods (one exhaust, one intake), the rocker pedestal, = and two rockers...then turn the motor over by hand two full turns. While this method wont be= exact, if the engine didn't stop when you were turning it you most likely instal= led the cam correctly. If it felt like it stopped at one point and wouldn't go further, chances are a pisto= n is hitting a valve and you need to disassemble things and go back to the dot to = dot part, OR, your cam is huge a= nd the piston to valve clearance is ZERO (it'd take a really big cam for this to happen)=

Do a second pass at 50lbft, and finally a 3rd at 70lbft.

Finally install the 5 smaller ARP bolts and torque them to 22lbft.

<= /p>

Insert all 16 pushrods (7.400" is probably needed unless you have highly milled heads or a small cam, in wh= ich 7.350" might be needed), place pedestal back on the head, apply locktite to all the rocker center bolts and reinsta= ll all the rockers. Torque the rockers to 22lbft.
Now, using your 24mm socket wrench, turn the motor over by hand (should be difficult as you are now building compression) and make sure the motor tu= rns over by hand a full 720 degrees, then turn it another 360 (doesnt have to be exact or anything).

Go over all the rockers again with your wrench just to make sure they are= all at 22-24'ish lbft.

Part 5 Complete
One m= ore part to go and we're done, hang in there.

Part 6: Reinstall everything else that was removed<= span style=3D'font-size:8.5pt;font-family:Verdana;color:red'>
Time = to complete: 2-4 hours

<= /p>

First, make sure you can see a few things before we put the intake manifold on. Find the electrical connector that plugs into the back of the intake manifold, the little vacuum hose that p= lugs in right next to it, and then also make sure your PCV hoses are all in pl= ace back there

Optional: (if you bought a brand new intake manifold)<= span style=3D'font-size:8.5pt;font-family:Verdana;color:red'>
If you bought a new intake manifold (2001+ style), now is the time to swap the hardware from your= old one over to the new one. Unbolt the fuel rail from the old intake manif= old, and while holding the intake manifold down firmly, pull UP on the fuel = rail and it should pop loose. Firmly press it into place on the new intake manifold and reinstall the bolts and torque them to 7 lbft (not very tight).

Install the two coolant plugs that came with your manifold on the back = two coolant holes on the heads, and install the front crossover pipe. The b= olts only need to be torqued to 9ftlbs (106 INCH= /lbs).

Transfer over the brake booster hose, this<= /st1:PersonName> will be very tough to disc= onnect most likely. That should be it! Now proceed with the instructions using your new manifold in place of the old.

Next, install the coolant crossover X pipe (if still using the old 97-00 style intake manifold), the 4 double ended bolts should be torqued to 9ftlbs (106 INCH/lbs).

Now, place the rear 4 8mm intake manifold bolts into the holes in the int= ake manifold (remember, the drivers side rearmost 2 bolts hold on a metal bra= cket that keeps the fuel rail from breaking off in a collision, so put this bracket back on = if you removed it) and slide the intake manifold into place. Before you put it a= ll the way back there, snake the brake booster line through the wires and ma= ke sure its got a clear path back to the brake bo= oster. Then, reconnect the electrical connector and the mini-vacuum line that go= es to the back as well. Now, try to get the intake manifold to seat properly= on the heads. You'll know when it seats at it'll stick in place and feel sol= id. Now connect the rubber brake booster hose back to the brake booster and reinstall the hose clamp.

Hand thread in the rest of the 10 bolts now. Once all 10 intake manifold bolts are hand threaded as far as they'll go, tighten them down with a wr= ench and then torque in the order shown in the picture on the left. You need to torque these down in a 2-pass fashion..the first pass, tighten to 44 INCH-lbs, then, on the 2nd pass torque t= hem to 89 INCH-lbs. NOTE: These are inch pounds, NOT foot pound= s!

Go ahead and sort out your wiring harness mess and reconnect the 8 fuel i= njectors, the EVAP solenoid connector (bright red plastic connector), reattach the = evap hose to the brass fitting on the front of the = drivers side of the manifold, and reconnect your PCV= valve to the rubber grommet on the front of the passenger side of the manifold.= The PVC line has a grounding strap that attaches to the front passenger side coolant pipe bolt stud...reconnect this.

<= /p>

Option 1: (if installin= g a new set of headers)
N= ow, if you have NEW headers to install, install them now. I won't go in= to the install of a new set of headers for now, but this is a good time to install = them if you bought them at the same time as your heads/cam.

Option 2: (if you alrea= dy had headers)
I= f you already had headers, slide the headers back into place. Put a header bo= lt through the flange, lay the gasket so it hangs on that bolt and stays in place, and then try to start threading the bolt into the appropriate ho= le in the head. Once you get one bolt started, line up a second, make sure= it goes through the hole in the gasket, and start that in the head. Only S= TART threading each bolt in until you get all 6 in, then= tighten them all down. They only need to be 18lbft so just make them sn= ug. Now you should be able to reconnect the collector flanges. Reconnect yo= ur O2 wire harnesses now.

Option 3: (if you still have stock exhaust manifolds)<= span style=3D'font-size:8.5pt;font-family:Verdana;color:red'>
L= ay the exhaust manifold back into place, making sure the old gasket goes back = in place and gets sandwiched in there. It may take 2 people to get the 3 s= tuds to go through the triangle shaped 3 hole connection on the stock Hpipe, but once it goes through, hand thread on t= he nuts as far as you can go. Reconnect the O2 wire harness now.

Back up in the engine bay, put an exhaust manifold bolt through the fla= nge, lay the gasket so it hangs on that bolt and stays in place, and then tr= y to start threading the bolt into the appropriate hole in the head. Once you get one bolt started, line up a second, make sure it goes through the h= ole in the gasket, and start that in the head. Only START threading each bo= lt in until you get all 6 in, then tighten them= down. They only need to be 18lbft so just make them snug.

Now= , stab your oil dipstick tube back into place. This<= /st1:PersonName> part may be easier if somebody gets under the car and feels around for the hole it goes in and guides it by hand. The process can take 5-10 minutes = of searching until the tube goes in just right. Once lined up with the hole give it a good push and it'll snap in. Then rea= ttach the holddown bolt to the head using the 15mm = bolt.

<= /p>

Grab a friend again and work the radiator/fan assembly back in= to place, again making sure you don't snag any wires. Once in place, try to = set the AC condensor tabs back into the slots on = the front of the radiator so they are attached.

Now, re-attach the power steering bracket/pump assembly to your drivers side head. I usually leave the hard to get t= o 15mm bolt out and just put in the 3 easy ones.

Reinstall the waterpump now, using new gasket= s if you bought them. Hand thread in all 6 waterpump bolts as far as you can, then finish the job off with a wrench. Torque the waterpump bolts in a 2 pass sequence, first to 11lbft, then do a second pass and tighten them to 22lbft. Reconnect the 4 hoses that go to the water pump, 2 big ones that go to the radiator, and 2 medium ones that go to the heater core. Work the metal hose clamps back into place.

Route the drivebelt back into place. It will = only route properly one way, so make sure you get it right. There should be a reference picture of the belt routing in the engine bay. Using a 15mm wre= nch on the tensioner, loosen the tensioner and slide the belt on.

Finally, underneath the front of the car, reconnect the 2 connections for= the electric cooling fans and re-secure the wiring harness to the fan shroud using the plastic clips that are attached to the fan shroud. Make sure you have closed the radiator drain valve as well.

<= /p>

Reinstall your valve covers. '99+ years use 4 8mm center bolts while '98 models use perimeter bolts. The valve covers use a rubber gaske= t so torque isn't important here,= the GM book calls for about 8lbft on the bolts, which means just make them ti= ght enough until they compress the gaskets to ensure a tight fit. Once the va= lve covers are on, on the drivers side you need to push the PCV hose tube into the grommet on the rear of the valve cover, and on the passenger side you need to connect the rubber PCV boot to the rear of the valve cover.

Now reinstall your coil packs. NOTE: I leave off the back hard to get to = coil pack rail bolts ('99 and up only) to make rail removal easier in the futu= re.

Reinstall your AIR tubes. You'll need to use NEW air tube gaskets and aga= in you need to hand thread in the 10mm bolts to the exhaust manifolds/header= s to ensure you don't crossthread them. The GM spe= c on those bolts is 15lbft, but I= just make 'em tight (you'll get good at estimating torque values so you don't have to use the torque wrench on all the non-critical bolts). Make sure you reconnect the rubber hoses to the metal AIR tubes.

Reconnect all 8 of your spark plug wires, the should<= /span> snap once on the spark plug end, and twice on the coil pack end. Now, snap your rubber fuel line back onto the fuel rail connection by pushing it on until it clicks. Make sure its firmly attached= by giving it a firm tug.

<= /p>

Re-bolt the 3 10mm bolts on to hold your throttle body to the intake manifold. These should to= rqued to 8lbft. Reconnect the electrical connections going to the throttlebody now. Reconnect your throttle cables by opening the TB by hand and locking the metal block on the end of the cable into the hole on the throttle "cam". Snap on your Cruise control cable now too (on non TCS cars).=

Reconnect your coolant lines (if you don't have a TB bypass installed) to= the throttlebody and connect the coolant line bac= k to the radiator now as well. While you are there, reconnect the final rubber line to your radiator, this = one should go to your coolant overflow fill tank. Once the two small lines are reconnected to the radiator, reinstall your radiator shroud. It's held on= by 4 10mm bolts, just make them snug. Now reinstall your maf/coupler/airlid assembly you removed earlier and reconnect the MAF and air intake electri= cal connectors, and rubber AIR hose (on 2000+ models).

<= /p>

Fill the radiator with coolant and water until it doesnt seem to keep going down. It should take one = full coolant bottle of DEXCOOL, and about 1.2 full coolant bottles of water. I don't premix the coolant/water since I know its about one bottle each anyway. Now reconnect battery.

Check your oil level at this= time and add any if needed.

Part 6 Complete
Now <= span class=3DGramE>lets get ready to fire this sucker up.

The big test! Starting it all up
Time = to complete: 30 minutes

<= /p>

First and foremost, look over EVERYWHERE in your engine bay for stuff that is disconnected. Make sure no fluids are hitting= the floor or dripping, make sure there are no elec= trical connections unconnected, etc. Take 15-20 minutes looking for anything, do= uble checking everything. Take the coolant fill cap off so we can watch the coolant level and let air bubbles work themselves out.

Now, make sure the radiator cap is removed and the coil packs are disconnected from the wiring harness (leave the spark plug wires all connected, just d= isconnect the wiring harness going to the pa= cks), and get in the car. Insert the key and turn the motor over for 4 seconds.= ..it wont start as long as you've disconnected the coil pack wires.

If the car turned over fine, connect the coil pack wires. Now, PREPARE YOURSELF. There are a few things you need to know before you turn the key= :
1) The engine is goin= g to be REALLY noisy for about 4-5 seconds. This is because the lifters need to pump up with = oil.
2) Your oil pressure needs to be watched like a hawk on this first startup. It should take 3-5 seconds= to come up to 30-50psi at idle.
3) Smoke will start coming out of your engine bay like mad for the first 5 minutes. This is normal and is just coolant/oil/grease/fingerp= rints burning off all the stuff you touched.

...Now...Turn the key being sure to keep an eye on the oil pressure guage. Make SURE oil pressure comes up withi= n 5 seconds (it'll take a few seconds since the motor has been apart and you = may have swapped the oil pump) and if it doesn't, shut the car off. The car should idle really poorly (depending on how big you went with the cam), a= nd rpms will fluctuate a lot. If it keeps trying to di= e, give it 5% throttle just to keep it idling and slowly back the throttle o= ff until it knows how to stay alive on its own. If all is going well, let the car idle up to full temperature, making sure to constantly watch the radiator and refill as necessary.

once car reaches full temp, shut it off and reinstall the coolant fill cap. You are ready for your test drive! For the first day, cruise around in = the car as long as you like and get the car nice and hot, full operating temperature. Don't take the RPMS over 4000 until the springs have a chanc= e to cool overnight. The next day you can take the car to redline, just rememb= er that HIGH rpms on cold valve springs is bad, make sure your engine is warm before you beat on your car from now= on. Stiffer springs need a little more care in th= is area.

Final Notes:
- After you have 100 miles on it, its probably good to go change the oil, re-check the coolant level and power steering level, and enjoy!

- Remember, with stiffer valve springs it becomes more important to make = sure your car is fully warmed up = before you take it to high rpms, as the springs are = more brittle and prone to breaking when cold.

- If you have a check engine light, use an autotap scanner to pull the codes. A common code at this point is P0300, and may happ= en from time to time when idling depending on the size of your camshaft.

- Your car will try to die once you rev it up some and let off. this will make= it difficult to drive at first, but after 100-200 miles of city drivi= ng it will learn itself out. If it doesn't, programming may be able to fix t= he issue or you can drill a small hole in your = throttlebody blade to let more air in at idle.

- More valvetrain noise is normal, depending on the = ramp rates your new cam has. More agressive cams W= ILL make the engine sound like a sewing machine, especially when you are insi= de the car driving with the windows up and radio off. This is normal.

	End of install Congr= ats, you've finished the install!=